CalcTrace

Deck Materials and Cost Calculator

Enter the size of a rectangular deck and the spacings you plan to build to. The calculator counts the board rows and stock lengths of decking, the joists, bearers and stumps under them, the screws and the oil or stain, then prices each line with the figures from your own quotes.

Last updated .

Your deck

m
m

Boards run along the length, so the number of board rows is counted across the width. Joists run across the width under the boards, and bearers run along the length under the joists.

Decking boards

mm
mm
m

The length you buy boards in, for example 5.4 m. Rows longer than this need a join, which must land on a joist.

Frame and footings

mm

450 mm is a common example. The right spacing depends on the board species and thickness: check the board maker's instructions, the span tables for your timber, or the NCC.

m
m

Bearer spacing is the joist span, and stump spacing is the bearer span. Both depend on timber size, grade and loads: take them from the span tables for your timber or from your engineer, and check with your local council.

Fixings, finish and waste

m²/L
%

Added to boards, joists, bearers and screws for splits, defects and cutting.

Unit prices

Every default is an example price, replace with your quote.

%

Result

MaterialQuantity

Cost

ItemQuantityUnit priceCost

A materials estimate for a simple rectangular deck. Spans, footing sizes and fixings must come from the span tables for your timber, the manufacturer and your local council. Prices are the ones you entered, not market rates.

Show the working

    How the deck is measured

    The calculator assumes a simple rectangular deck built in three layers: bearers sitting on stumps or posts, joists sitting across the bearers, and decking boards fixed across the joists. Boards run along the length L, joists run across the width W, and bearers run along the length again. All lengths are in metres unless marked mm.

    Board rows: nb = ⌈(W + g) ÷ (b + g)⌉

    b is the board width and g the gap, both converted to metres. Each board takes up b + g of the width; adding one gap to W allows for there being one fewer gap than boards. The last row is usually ripped down to fit.

    Lineal metres of decking = nb × L

    Stock lengths: if L ≤ S, k = ⌊S ÷ L⌋ rows per length and N = ⌈nb ÷ k⌉; if L > S, f = ⌊L ÷ S⌋ full lengths per row, r = L − f × S, and N = nb × f + ⌈nb ÷ ⌊S ÷ r⌋⌉

    S is the stock length you buy. The short piece r that finishes each row is cut from further lengths, as many as fit, so offcuts are used where they can be. The waste allowance is then added and N rounded up again.

    Joists: nj = ⌈L ÷ sj⌉ + 1, each W long   Bearers: nbr = ⌈W ÷ sb⌉ + 1, each L long

    Stumps: ns = nbr × (⌈L ÷ sp⌉ + 1)   Screws = nb × nj × screws per crossing

    Oil or stain (litres) = L × W × coats ÷ coverage per litre

    sj, sb and sp are the joist, bearer and stump spacings. Rounding up and adding one puts a member at each end and keeps the actual spacing at or below the one you entered.

    Worked example: a 6 m × 4.8 m deck

    1. Board rows. With 90 mm boards and 5 mm gaps, (4,800 + 5) ÷ 95 = 50.58, so 51 rows. They cover 51 × 90 + 50 × 5 = 4,840 mm, so the last board is ripped by 40 mm.
    2. Decking. 51 × 6 = 306 lineal metres laid.
    3. Stock lengths. A 6 m row needs one 5.4 m length plus 0.6 m. One 5.4 m length gives 9 of those 0.6 m pieces, so 51 + ⌈51 ÷ 9⌉ = 51 + 6 = 57 lengths. With 10% waste, 57 × 1.1 = 62.7, so buy 63 lengths, or 63 × 5.4 = 340.2 m.
    4. Joists. 6,000 ÷ 450 = 13.33, rounded up to 14 spaces, so 15 joists at 428.6 mm centres. 15 × 4.8 = 72 m, or 79.2 m with waste.
    5. Bearers. 4.8 ÷ 1.8 = 2.67, so 3 spaces and 4 bearers, each 6 m: 24 m, or 26.4 m with waste.
    6. Stumps. 6 ÷ 1.8 = 3.33, so 4 spaces and 5 stumps per bearer: 4 × 5 = 20 stumps.
    7. Screws. 51 rows × 15 joists × 2 = 1,530 screws, 1,683 with waste, which is 4 boxes of 500.
    8. Oil. The deck is 28.8 m². Two coats at 10 m² per litre need 28.8 × 2 ÷ 10 = 5.76 litres.
    9. Cost at the example prices. Boards 340.2 m × $8 = $2,721.60; joists 79.2 m × $12 = $950.40; bearers 26.4 m × $18 = $475.20; stumps 20 × $35 = $700; screws 4 × $60 = $240; oil 5.76 L × $30 = $172.80. The subtotal is $5,260.00, 10% contingency adds $526.00, and the total is $5,786.00.

    Reading the result and common mistakes

    Spacings are the critical inputs. The joist spacing is set by how far the boards can span, the bearer spacing by how far the joists can span, and the stump spacing by how far the bearers can span. Each depends on timber species, stress grade, member size and whether the member is continuous over a support. None of the defaults here is a structural recommendation. Take them from the board maker's instructions and the span tables for your timber, and check with your local council whether the deck needs approval.

    Joins. Where rows are longer than your stock board, every join must fall on a joist, often with a doubled joist or two screws each side. If you want staggered joins, the offcut sharing assumed above will not always work and you may need a few more lengths.

    What is left out. Footing concrete, stirrups and bracing, joist hangers and tie-downs, blocking, fascia boards, steps and balustrades are not counted. Joist and bearer timber is given in lineal metres; buy it in lengths that suit the spans so that joins land over supports. Board orientation matters too: if your boards run across the width instead, swap the length and width.