How the fence is counted
Start with the length that is actually fenced, the total length less the gate openings, then divide it into bays between posts. All lengths are in metres.
Lnet = L − G × wg Bays: n = ⌈Lnet ÷ s⌉
L is the total fence line, G the number of gates, wg the gate opening and s the post spacing. For a steel sheet panel fence, s is the panel width, because a post goes at every panel joint.
Posts = n + 1 + (E − 2) + G
A straight run of n bays needs n + 1 posts, including its two end posts. E is the number of end and corner posts: each one beyond the first two starts a new run and adds a post. Each gate splits a run in two and adds one more, so there is a post on each side of every opening. A fence that closes on itself, such as a full loop, needs one post fewer than this.
Rails = n × rails per bay Palings = ⌈Lnet ÷ (p − o)⌉
p is the paling width and o the overlap, so each paling adds p − o to the fence. Pool fence panels are counted the same way as bays: ⌈Lnet ÷ panel width⌉.
Concrete per hole V = π × (d ÷ 2)² × h Bags = ⌈posts × V × (1 + waste) ÷ bag yield⌉
d is the hole diameter and h its depth. The post itself takes up some of the hole, so this slightly overstates the concrete, which covers spillage. Each post must be the fence height plus the hole depth long.
Worked example: 30 m of paling fence with one gate
- Fenced length. 30 − 1 × 0.9 = 29.1 m.
- Bays. 29.1 ÷ 2.4 = 12.13, so 13 bays at 2.24 m.
- Posts. 13 + 1 + 0 + 1 = 15 posts, each at least 1.8 + 0.6 = 2.4 m long.
- Rails. 13 × 3 = 39 rails (87.3 m), or 43 with 10% waste.
- Palings. Each 150 mm paling with a 25 mm overlap adds 125 mm: 29,100 ÷ 125 = 232.8, so 233 palings, or 257 with waste.
- Concrete. A 300 mm hole 600 mm deep holds π × 0.15² × 0.6 = 0.0424 m³. Fifteen holes take 0.636 m³, or 0.700 m³ with waste, which is 70 bags at 0.01 m³ each.
- Cost at the example prices. Posts 15 × $30 = $450; rails 43 × $12 = $516; palings 257 × $3.50 = $899.50; gate $250; concrete 70 × $10 = $700. The subtotal is $2,815.50, 10% contingency adds $281.55, and the total is $3,097.05.
The same line as a steel sheet panel fence with 2.365 m panels needs 29.1 ÷ 2.365 = 12.30, so 13 panels and 15 posts. At $150 a panel the materials come to $1,950 + $450 + $250 + $700 = $3,350, or $3,685 with contingency. As a pool fence with 1.2 m panels it needs 29.1 ÷ 1.2 = 24.25, so 25 panels: at $250 each plus the gate, $6,500, or $7,150 with contingency.
Reading the result
Bays come out shorter than the spacing you enter. The calculator rounds the number of bays up and spaces the posts evenly, so 2.4 m becomes 2.24 m in the example. That keeps every bay within your maximum, and rails cut from 2.4 m stock still reach.
Panels rarely fit exactly. The last steel or pool panel is usually cut down or made to measure. Glass cannot be cut on site, so a glass fence is normally set out with panels of several widths; ask the supplier to lay it out from your measurements.
Pool fences are regulated. AS 1926.1 is the Australian Standard for pool safety barriers, and the NCC and each state's pool laws set what applies to your pool. This calculator does not check compliance.
Boundary fences. A dividing fence usually needs the neighbour's agreement and the cost is often shared under state law. Check with your council before you start.
Footings. For the concrete itself, or for larger footings, use the concrete calculator. Hole size here is an example: deeper or wider holes are common for tall or exposed fences.