CalcTrace

Rainwater Tank Size Calculator

Work out how much rain your roof can collect, run a month-by-month water balance for a tank size you choose, and see how much of your household's demand it meets, how often it overflows and the smallest tank from your list that reaches your target.

Last updated .

Roof and rainfall

m²

The plan area of the roof that drains to the tank: its footprint seen from above, not the sloping surface.

Rainfall

Use the Bureau of Meteorology climate statistics for the station nearest you at bom.gov.au: the mean rainfall for each month, or the annual mean. The values filled in are an example pattern, not any real place.

0–1

The share of rain that reaches the tank after losses to first flush, evaporation, splash and gutters overflowing. 0.8 is a typical assumption.

L

Litres diverted each time it rains.

/yr

Only used with a diverter.

Household demand

Enter demand as

Count only the uses plumbed to the tank. The litres per person are examples: a water bill or meter reading gives your own.

L/day
L/day
L/day

Tank

L

Litres, separated by spaces. Replace them with the sizes your supplier sells.

%

Result

Over a typical yearValue
Tank sizeDemand metOverflow
MonthRainInto tankUsedShortOverflowFull at end

A monthly water balance for an average year, in litres. Real years are wetter or drier than the average, and a monthly step smooths out dry spells within a month, so treat small tanks' results as optimistic and allow a margin.

Show the working

    How much water a roof collects

    Litres harvested = A × R × C

    A is the roof catchment area in m², measured in plan (the footprint from above, because rain falls vertically, so a steep roof catches no more than a flat one of the same footprint). R is the rainfall in mm and C the runoff efficiency, the share that actually reaches the tank. The rule that makes this easy is exact: 1 mm of rain on 1 m² is 0.001 m³, which is 1 litre. A first-flush diverter then takes a fixed volume each time it rains, so the calculator subtracts diverter litres × rain events, sharing the year's events between the months in proportion to their rainfall.

    Monthly balance: Send = min(capacity, Sstart + inflow − used)

    Each month the tank starts with what was left from the month before (Sstart), the month's harvest comes in, the month's demand (litres per day × days in the month) is drawn from what is there, and anything left above the tank's capacity overflows. Water not supplied is the shortfall, which mains water or a delivery has to cover. The year is run twice: the first year starts with an empty tank and the second starts from whatever the first left behind, which removes the effect of the empty start. The figures shown are for the second year. The share of demand met is the water supplied divided by the year's demand.

    The suggested size repeats the balance for every size in your list, smallest first, and picks the first one that meets your target share.

    Worked example

    The defaults use a 150 m² roof, an efficiency of 0.8, an example rainfall pattern of 600 mm a year with a wet summer and a dry winter, no diverter, and three people using 20 L each a day for the toilet, laundry and garden: 3 × 60 = 180 L a day.

    1. Harvest. 150 × 600 × 0.8 = 72,000 L a year. January brings 150 × 110 × 0.8 = 13,200 L.
    2. Demand. 180 × 365 = 65,700 L a year, or 180 × 31 = 5,580 L in January. The roof collects more than the house uses over a year, but not in the right months.
    3. A 5,000 L tank. It starts the second year full, overflows through the wet months from December to March, and runs dry from June to October, when only that month's rain can be used. Over the year it supplies 48,980 L, 74.6% of demand, leaving a 16,720 L shortfall, while 23,020 L overflows. As a check, 48,980 + 23,020 = 72,000 L, all the water that came in, because the tank ends the year as full as it began.
    4. Choosing a size. Running the same year for each standard size gives 68.5% for 1,000 L, 82.2% for 10,000 L, 89.8% for 15,000 L, 97.4% for 20,000 L and 100% for 30,000 L. For an 80% target the suggestion is 10,000 L.
    5. First flush. A 20 L diverter and 50 rain events a year take 20 × 50 = 1,000 L. January has 110 ÷ 600 of the rain, so 9.17 events and about 183 L diverted.

    Enter the same 600 mm as an annual total instead and the 5,000 L tank appears to meet 100% of demand, because rain spread evenly over the year always exceeds 180 L a day. That gap is why monthly rainfall matters: storage exists to carry water from wet months into dry ones, and an annual figure cannot show it.

    Where to get rainfall figures

    Use the Bureau of Meteorology climate statistics for the station nearest you, at bom.gov.au, and copy the mean rainfall for each month. A station with a long record gives a steadier average. Rainfall can change a lot over a few kilometres, especially near hills and the coast, so pick a station with similar terrain if you can. No city averages are quoted here.

    How to read the result

    An average year is not every year. In a dry year the tank empties sooner and stays empty longer. If the supply really matters, as for a house without mains water, size for a dry year: enter the monthly rainfall from a dry year on record and see what the tank delivers.

    Monthly steps flatter small tanks. Within a month, rain comes in a few storms and demand is spread across the days. A small tank overflows during a storm and runs dry before the next, which a monthly balance does not see. Daily models are more reliable for tanks of a few thousand litres; treat this one as optimistic for them.

    Efficiency and demand are assumptions. Dirty gutters, leaf screens and a large first flush all lower the efficiency. Garden use is seasonal, so a constant daily figure overstates winter use and understates summer use. Check your council and state rules on tanks and on what the water may be plumbed to.