CalcTrace

Roofing Calculator

Work out the true sloped area of a roof from the building's footprint, the overhang and the roof pitch, given in degrees or as a rise over run. Add a waste allowance and the coverage of your sheets, tiles or bundles to see how many to order.

Last updated .

The building and the roof

Units
m
m
mm
mm

Measure the walls from the outside. Overhangs are measured level, not along the slope. On a gable roof the end overhang is the verge; on a hip roof it is the eaves at the ends.

Roof pitch given as
°
%
m²

The coverage is an example, not a figure for any product. Use the effective coverage the manufacturer states, which allows for side laps and end laps.

Result

Roof area, along the slope

–

–Plan area with overhangs
–Pitch factor
–Area with waste
–Sheets or bundles
MeasureValue

Assumes every roof face has the same pitch. Ridge, hip and valley capping, flashings and gutters are measured by length and are not included.

Show the working

    The plan-area method

    Measuring a roof on the slope is awkward and unsafe. It is easier to measure the building on the ground, add the overhangs to get the area the roof covers seen from above, and then scale that up for the slope. The scale-up is the pitch factor.

    Plan area = (L + 2 × e) × (W + 2 × o)

    L is the length of the building along the ridge, W its width (the span), o the overhang at the eaves on each long side and e the overhang at each end. All measurements are level, in the same unit.

    Pitch factor = 1 ÷ cos θ = √(1 + (rise ÷ run)²)

    θ is the pitch angle above horizontal. When the pitch is given as a rise over a run, the two forms are the same thing, because cos θ = run ÷ slope length and the slope length is √(rise² + run²) by Pythagoras.

    Roof area = plan area × pitch factor

    Sheets or bundles = roof area × (1 + waste % ÷ 100) ÷ coverage of one, rounded up

    Worked example: a 12 m by 8 m house

    The walls measure 12 m by 8 m, with 600 mm overhangs all round and a pitch of 22.5°.

    1. Plan area. (12 + 1.2) × (8 + 1.2) = 13.2 × 9.2 = 121.44 m².
    2. Pitch factor. cos 22.5° = 0.92388, so the factor is 1 ÷ 0.92388 = 1.0824.
    3. Roof area. 121.44 × 1.0824 = 131.45 m².
    4. Waste. 131.45 × 1.10 = 144.59 m².
    5. Count. At the example coverage of 3 m² each, 144.59 ÷ 3 = 48.2, so 49.

    If the pitch is given as 5 in 12, the factor is √(1 + (5 ÷ 12)²) = 13 ÷ 12 = 1.0833, and the angle is 22.62°. In imperial units, a 40 ft by 30 ft house with 1 ft overhangs has a plan area of 42 × 32 = 1,344 ft². At 6 in 12 the factor is 1.1180, so the roof is 1,502.6 ft², or 15.03 roofing squares of 100 ft².

    For a gable roof the same numbers give the rafter length from the edge of the eaves to the ridge: half the span plus the eaves overhang, times the factor, (4 + 0.6) × 1.0824 = 4.98 m. The ridge sits 4 × tan 22.5° = 1.66 m above the top of the walls.

    Pitch factors

    PitchFactorPitchFactor
    10°1.01544 in 12 (18.43°)1.0541
    15°1.03535 in 12 (22.62°)1.0833
    20°1.06426 in 12 (26.57°)1.1180
    25°1.10348 in 12 (33.69°)1.2019
    30°1.154712 in 12 (45°)1.4142

    Why it works for gable and hip roofs alike

    Every flat roof face is a plane tilted at the pitch angle. Seen from directly above, the face looks shorter in the direction of the slope by the factor cos θ, and unchanged across the slope, so its true area is its plan area divided by cos θ. That holds whatever the outline of the face: the rectangles of a gable, or the triangles and trapezoids of a hip.

    Seen from above, the faces of a roof fit together edge to edge and fill the plan area exactly once. If every face has the same pitch, each one is scaled by the same factor, so the total is the plan area times that factor. A hip roof on the same walls with the same pitch therefore has the same roof area as a gable roof with overhangs at the ends. It is different from the gable in other ways, which do not change the area: it has more cutting, so it usually needs more waste, and it has hip lines to cap.

    The method stops working when faces have different pitches, as on a roof with steeper hip ends, a mansard roof or a flatter verandah roof joined to the main roof. Work out each part separately with its own pitch and add them. Dormers, skylights and curved roofs also need separate treatment.

    Common mistakes

    Measuring the overhang along the slope. The formula needs the level distance. On a 22.5° roof, 600 mm level is 649 mm along the slope.

    Treating the factor as a percentage of the pitch. A 45° roof is not 45% bigger than its plan; it is 41.4% bigger. Low pitches add little: 10° adds only 1.5%.

    Using the full sheet width for coverage. Overlapping sheets lose one rib or more at each side lap, and tiles and shingles lose their head lap, so the effective coverage is always less than the size of the product.