CalcTrace

Ohm's Law Calculator

Enter any two of voltage, current, resistance and power to get the other two. Every field takes a prefix, so you can work in millivolts, milliamps, kilohms or kilowatts without converting first.

Last updated .

Enter any two values

Leave the two values you want to find empty. Values must be greater than zero; for a reversed current, enter its size.

Result

Result

–

–Voltage
–Current
–Resistance
–Power
QuantityValue in base unitsFormula
Show the working

    Ohm's law and the power formula

    Two relationships connect the four quantities in a simple circuit. The first is Ohm's law, named after Georg Simon Ohm, who published it in 1827. The second is the definition of electrical power.

    V = I × R

    P = V × I

    V is the voltage across the component in volts (V), I is the current through it in amperes (A), R is its resistance in ohms (Ω) and P is the power it converts to heat, light or work, in watts (W). One volt drives one ampere through one ohm, and one volt times one ampere is one watt.

    With two equations and four quantities, knowing any two fixes the other two. There are six possible pairs, and substituting one equation into the other gives every combination. For example, putting I = V ÷ R into P = V × I gives P = V² ÷ R, and putting V = I × R into it gives P = I² × R.

    The formula wheel

    The twelve rearrangements are often drawn as a wheel. The circle is cut into four quarters, one for each quantity, and each quarter holds the three ways of getting that quantity from two of the others. To use it, find the quarter for the value you want, then pick the formula that uses the two values you have.

    VI PR I × RP ÷ I√(P × R) V ÷ RP ÷ V√(P ÷ R) V × II² × RV² ÷ R V ÷ IV² ÷ PP ÷ I²
    To findFormulas
    Voltage VI × R,  P ÷ I,  √(P × R)
    Current IV ÷ R,  P ÷ V,  √(P ÷ R)
    Resistance RV ÷ I,  V² ÷ P,  P ÷ I²
    Power PV × I,  I² × R,  V² ÷ R

    Worked example: 9 V across 4.7 kΩ

    1. Convert to base units. 4.7 kΩ is 4.7 × 1,000 = 4,700 Ω. The voltage is already in volts.
    2. Current. I = V ÷ R = 9 ÷ 4,700 = 0.0019149 A. Multiply by 1,000 to express it in milliamps: 1.915 mA.
    3. Power. P = V² ÷ R = 81 ÷ 4,700 = 0.017234 W, or 17.23 mW.
    4. Check. P = V × I = 9 × 0.0019149 = 0.017234 W, the same answer by a second route.

    A small quarter-watt resistor would run cool here. Now suppose the prefix is dropped and the resistor is read as 4.7 Ω. The current becomes 9 ÷ 4.7 = 1.915 A and the power 17.23 W, a thousand times more of each. A slip of one prefix is the most common error in these sums, which is why every field above has its own prefix menu.

    Two more examples

    A heater. A 2,000 W element on a 230 V supply draws I = P ÷ V = 2,000 ÷ 230 = 8.70 A and has a working resistance of R = V² ÷ P = 52,900 ÷ 2,000 = 26.45 Ω.

    A resistor for an LED. An LED does not obey Ohm's law, but the resistor in series with it does. With a 5 V supply, an LED that drops 2 V and a target of 20 mA, the resistor sees 5 − 2 = 3 V. R = 3 ÷ 0.02 = 150 Ω, and it dissipates P = 3 × 0.02 = 0.06 W, or 60 mW. Enter 3 V and 20 mA above to check.

    Where the formulas stop being reliable

    Ohmic parts only. V = IR describes components whose resistance stays put as the voltage changes: ordinary resistors, wires and heating elements at a steady temperature. Diodes, LEDs, transistors and gas discharge lamps are not ohmic. You can still divide V by I at one operating point, but that ratio changes as soon as the voltage does.

    Temperature changes resistance. A filament lamp or heater element has a much lower resistance cold than hot, so it draws a surge of current when first switched on. Resistance measured with a meter on a cold element will not predict the running current.

    Alternating current. For purely resistive loads, use RMS voltage and current and the formulas hold as written. Motors, transformers, fluorescent ballasts and power supplies also have reactance, so the ratio of voltage to current is an impedance, and real power is V × I × the power factor. The calculator does not cover that case.

    Ratings are not results. The power figure tells you how much heat a resistor must shed. Choose a part rated comfortably above it, because a resistor run at its full rating gets very hot.