CalcTrace

Resistor Colour Code Calculator

Read the value, tolerance and temperature coefficient from a 4, 5 or 6-band resistor, or turn a value into its colour bands with the nearest E12 and E24 standard values. A third tab adds up resistors in series and in parallel.

Last updated .

What do you want to do?

Number of bands

Result

Resistance

–

––
––
––
––
Show the working

    How the colour code works

    Small through-hole resistors are too small to print a value on, so the value is painted on as coloured rings. The code is defined in the international standard IEC 60062. Each colour stands for a digit, and the same colours do other jobs depending on where the band sits.

    R = (significant digits) × 10m ohms,  within ± tolerance

    On a 4-band resistor the first two bands are digits, the third is the multiplier 10m and the fourth is the tolerance. A 5-band resistor has three digit bands, then the multiplier and tolerance, which allows values such as 10.2 kΩ that two digits cannot express. A 6-band resistor adds a sixth band for the temperature coefficient, in parts per million of the value per kelvin (ppm/K).

    ColourDigitMultiplierToleranceTemp. coefficient
    Black0× 1
    Brown1× 10± 1%100 ppm/K
    Red2× 100± 2%50 ppm/K
    Orange3× 1 k15 ppm/K
    Yellow4× 10 k25 ppm/K
    Green5× 100 k± 0.5%
    Blue6× 1 M± 0.25%10 ppm/K
    Violet7× 10 M± 0.1%5 ppm/K
    Grey8× 100 M
    White9× 1 G
    Gold× 0.1± 5%
    Silver× 0.01± 10%
    No band± 20%

    A blank cell means the calculator does not use that colour in that position. Some of those uses, such as grey as a tolerance, have been defined differently in different editions of the standard and by different makers, so check a part’s data sheet if you meet one.

    Worked examples

    4 bands: yellow, violet, red, gold. Yellow is 4 and violet is 7, giving 47. Red as a multiplier is × 100, so R = 47 × 100 = 4,700 Ω, or 4.7 kΩ. Gold is ± 5%, which is ± 235 Ω, so the real value can be anywhere from 4,465 Ω to 4,935 Ω.

    5 bands: brown, black, black, red, brown. The digits are 1, 0, 0, giving 100. Red multiplies by 100: 10,000 Ω, or 10 kΩ. Brown tolerance is ± 1%, so 9,900 Ω to 10,100 Ω.

    6 bands: the same with a brown sixth band. Brown in the sixth place is 100 ppm/K. If the resistor warms by 50 °C, its value can shift by 100 × 50 = 5,000 ppm, which is 0.5% or 50 Ω on 10 kΩ.

    Standard values: the E12 and E24 series

    Resistors are not made in every value. IEC 60063 defines series of preferred numbers spaced evenly on a logarithmic scale. E12 has 12 values in each decade: 10, 12, 15, 18, 22, 27, 33, 39, 47, 56, 68 and 82, each roughly 101/12 = 1.2115 times the one before. E24 adds 12 more in between: 11, 13, 16, 20, 24, 30, 36, 43, 51, 62, 75 and 91, with a step of about 101/24 = 1.1007. The same numbers repeat in every decade, so 4.7 Ω, 47 Ω, 470 Ω and 4.7 kΩ are all E12 values.

    Because the spacing is logarithmic, “nearest” is measured by ratio, not by difference. Take 5 kΩ. Its E12 neighbours are 4.7 kΩ, which is 6% below, and 5.6 kΩ, which is 12% above, so 4.7 kΩ is closer. In E24 the neighbour 5.1 kΩ is only 2% above and becomes the nearest value. In bands, 4.7 kΩ is yellow, violet, red on a 4-band part and yellow, violet, black, brown on a 5-band part, where the multiplier drops by one step because there is an extra digit.

    Resistors in series and parallel

    Series: R = R1 + R2 + … + Rn

    Parallel: 1 ÷ R = 1 ÷ R1 + 1 ÷ R2 + … + 1 ÷ Rn

    In series the same current flows through every resistor, so the resistances add: 100 + 220 + 470 = 790 Ω. In parallel each resistor offers another path, so the conductances (1 ÷ R) add: 1 ÷ (0.01 + 0.0045455 + 0.0021277) = 59.98 Ω. For two resistors this simplifies to the product over the sum, 100 × 220 ÷ 320 = 68.75 Ω. A parallel combination is always smaller than its smallest member, and n equal resistors in parallel give R ÷ n, so three 1 kΩ resistors make 333.3 Ω.

    Reading real resistors

    Find the starting end. The tolerance band is usually set slightly apart from the others, and gold or silver never appear as the first band. If a reading gives a value that is not in a standard series, try reading from the other end.

    Colours are hard to tell apart. Red, orange and brown, or violet and grey, are easily confused under warm lighting or on an aged part. When in doubt, measure the resistor with a multimeter, out of circuit, since other parts in a circuit give a false reading.

    Tolerance and series go together. E12 values are typically sold at ± 10% or better and E24 values at ± 5% or better. Precision parts at ± 1% and tighter usually come from the finer E96 series and use 5 bands.

    Surface-mount parts use printed number codes rather than colours, so this calculator does not cover them.