What scientific notation is
Scientific notation writes any number as a coefficient multiplied by a power of ten. It keeps very large and very small numbers readable, and it shows at a glance how many digits of the number are actually known.
number = a × 10n, with 1 ≤ |a| < 10 and n a whole number
Here a is the coefficient (also called the mantissa or significand), which has exactly one non-zero digit before the decimal point, and n is the exponent, which says how many places the decimal point was moved. A positive n means a large number and a negative n means a small one. The sign of the number itself is carried by a, not by n.
Two close relatives are in everyday use:
- E notation is the same thing typed on one line, for calculators, spreadsheets and code: 5.2E-4 means 5.2 × 10−4. The E stands for “exponent” and has nothing to do with the constant e.
- Engineering notation only uses exponents that are multiples of 3, with a coefficient from 1 up to 1,000, so that the power of ten lines up with the metric prefixes: 47,000 is 4.7 × 104 in scientific notation and 47 × 103 in engineering notation, which reads straight off as 47 kilo.
Worked example: converting 0.00052
- Find the significant digits. The leading zeros only position the decimal point. The digits that carry information are 5 and 2.
- Put the decimal point after the first of them. That gives the coefficient 5.2.
- Count how far the point moved. From 0.00052 to 5.2 it moved 4 places to the right. Moving right means the original number was small, so the exponent is −4.
- Write the result. 0.00052 = 5.2 × 10−4, or 5.2E-4.
- Engineering form. The nearest multiple of 3 below −4 is −6, two steps away, so move the point two more places: 520 × 10−6, or 520 micro.
A large number goes the other way. The speed of light, 299,792,458 metres per second, has its point moved 8 places to the left, giving 2.99792458 × 108. Rounded to three significant figures that is 3.00 × 108, and the two zeros must be written, because they say the value is known to three figures.
Arithmetic in scientific notation
Multiply: (a × 10m) × (b × 10n) = (a × b) × 10m+n
Divide: (a × 10m) ÷ (b × 10n) = (a ÷ b) × 10m−n
Add or subtract: rewrite both with the same power of ten, then add or subtract the coefficients
In each formula a and b are the two coefficients and m and n are their exponents. After any of these, the coefficient may have drifted outside the range 1 to 10 and has to be brought back.
- Multiplying. (6.4 × 105) × (2.5 × 10−3): 6.4 × 2.5 = 16 and 5 + (−3) = 2, giving 16 × 102. The coefficient is too big, so move the point one place and raise the exponent: 1.6 × 103.
- Dividing. (8.4 × 107) ÷ (2.1 × 103): 8.4 ÷ 2.1 = 4 and 7 − 3 = 4, giving 4.0 × 104.
- Adding. 3.2 × 104 + 5.6 × 103: rewrite the second as 0.56 × 104, then 3.2 + 0.56 = 3.76, giving 3.76 × 104 before rounding.
Significant figures
Scientific notation removes the guesswork about which digits are significant: every digit of the coefficient counts. In ordinary notation the rules are:
- Leading zeros never count. 0.00520 has three significant figures: 5, 2 and the final 0.
- Zeros after the last non-zero digit count only if there is a decimal point. 1200 is taken to have two significant figures, while 1200. and 1.200 × 103 both have four.
A calculated answer cannot be more precise than the numbers that went into it. For multiplication and division, keep as many significant figures as the input that has the fewest. For addition and subtraction, it is decimal places that matter: keep the last place that every input has. In the addition above, 3.2 × 104 is only known to the nearest thousand, so 3.76 × 104 is reported as 3.8 × 104. The calculator shows both the unrounded and the rounded answer.
Common mistakes
Reading a negative exponent as a negative number. 5.2 × 10−4 is a small positive number. A negative number has the minus sign on the coefficient.
Leaving the coefficient out of range. 16 × 102 has the right value but is not in scientific notation. Normalise it to 1.6 × 103.
Typing “× 10” as well as the exponent key. The EXP or EE key on a calculator already means “times ten to the power”. Entering 5.2 × 10 EE −4 gives 5.2 × 10−3, ten times too large.
Dropping zeros that matter. Avogadro’s constant written out is 602,200,000,000,000,000,000,000 when given to four figures. In scientific notation it is 6.022 × 1023, which is shorter and also makes the four known digits explicit.