CalcTrace

Brick, Block and Mortar Calculator

Work out how many bricks or concrete blocks a wall needs after taking out doors and windows, then the mortar to lay them and the cement bags and sand that go into that mortar.

Last updated .

Your wall

Brick or block

Standard Australian brick: 230 × 110 × 76 mm (length × thickness × height).

mm
m
m
Skins (leaves)

Openings (doors and windows)

Leave a row blank if you do not need it.

%

Mortar

Defaults are typical values, not product data. Replace them with your own where you have them.

Loose cement and damp sand fill more space than the set mortar they make. 1.27 is a common rule of thumb.

kg
kg/m³
kg/m³

Result

To orderQuantity
Wall and mortarValue

A material estimate for solid units with full mortar beds. It leaves out ties, lintels, cavity fill, lime, and mortar lost on site; the waste allowance covers the bricks or blocks only.

Show the working

    How the bricks and mortar are worked out

    Bricklayers estimate by area. Each brick or block, together with half of the mortar joint around it, takes up one rectangle on the face of the wall. Count how many of those rectangles fit in a square metre and multiply by the wall area left after the openings.

    Units per m² = 1 ÷ ((L + j) × (H + j))

    L is the length of the brick or block, H its height and j the mortar joint, all in metres. For a standard Australian brick, 230 mm long and 76 mm high, with 10 mm joints, the rectangle is 0.24 × 0.086 = 0.02064 m², so a single skin needs 1 ÷ 0.02064 = 48.45 bricks per m². A concrete block of 390 × 190 mm laid with 10 mm joints works to its nominal 400 × 200 mm, exactly 12.5 blocks per m².

    Net area = wall length × wall height − Σ (opening width × height × count)

    Units to order = ⌈net area × units per m² × skins × (1 + waste ÷ 100)⌉

    The mortar is whatever part of the wall is not brick. One square metre of a single skin T thick holds T cubic metres of wall, and the bricks in it take up their count times their own volume L × H × T.

    Wet mortar per m² = T − units per m² × (L × H × T)

    Wet mortar is the set volume in the joints. The cement and sand you buy are measured loose and dry, and loose materials have air between the grains, so the wet volume is multiplied by a dry-volume factor, 1.27 by default. The dry volume is then split by the mix ratio: with cement:sand of 1:5, cement is 1 part in 6 and sand 5 parts in 6. Each volume times its bulk density gives kilograms, and cement kilograms divided by the bag size, rounded up, gives bags.

    Worked example: a 10 m brick wall with a window and a door

    1. Areas. The wall is 10 m long and 2.4 m high, 24 m² gross. The window is 1.8 × 1.2 = 2.16 m² and the door 0.9 × 2.1 = 1.89 m², 4.05 m² of openings, so the net area is 19.95 m².
    2. Bricks. At 48.45 per m² a single skin needs 19.95 × 48.45 = 966.6 bricks. With 5% waste that is 1,014.9, rounded up to 1,015. A double skin doubles it to 2,030.
    3. Mortar per m². One brick is 0.23 × 0.076 × 0.11 = 0.0019228 m³, and 48.45 of them fill 0.09316 m³ of the 0.11 m³ in a square metre of wall. The joints hold 0.11 − 0.09316 = 0.01684 m³ of wet mortar per m², about 0.35 m³ for every 1,000 bricks.
    4. Mortar for the wall. 19.95 × 0.01684 = 0.336 m³ wet, and 0.336 × 1.27 = 0.4267 m³ dry.
    5. Cement. One sixth of 0.4267 is 0.0711 m³, and 0.0711 × 1,440 = 102.4 kg. That is 5.12 bags of 20 kg, so buy 6 bags.
    6. Sand. Five sixths of 0.4267 is 0.3556 m³, and 0.3556 × 1,600 = 569 kg.

    For a concrete block wall the same steps apply. A 190 mm block laid with 10 mm joints fills 0.0741 ÷ 0.08 = 92.6% of the wall face, which leaves 0.19 × (1 − 0.92625) = 0.0140 m³ of mortar per m² if every joint were filled across the full thickness.

    Reading the result and where it stops working

    Joint size matters more than it looks. Going from 10 mm to 12 mm joints with standard bricks drops the count to 1 ÷ (0.242 × 0.088) = 46.96 per m² and raises the wet mortar from 0.01684 to 0.01971 m³ per m², about 17% more. Measure the joint your bricklayer actually runs.

    Hollow and cored units. The mortar formula assumes solid units with mortar right across each bed. Hollow blocks are often laid on the two face shells only, and cored or frogged bricks take some mortar into the holes, so real mortar use can be noticeably lower or higher. Treat the mortar figure as a planning quantity and adjust the dry-volume factor once you know how your units behave.

    Double skin walls. The calculator doubles both the bricks and the mortar for two skins. It does not include a collar joint, cavity fill or the wall ties that join the skins.

    What the mix ratio leaves out. Many mortars include lime or an additive alongside the cement and sand. This page splits the dry volume between cement and sand only, so for a cement:lime:sand mix, work out the lime separately and use the mix your engineer, supplier or local building rules call for.

    Waste. The waste allowance covers broken and cut bricks or blocks. Mortar is also lost to droppings and to batches that go off; if that worries you, raise the dry-volume factor rather than the brick waste.