Surface area formulas for each solid
Surface area is the total area of the outside of a solid: the amount of paint, sheet metal, wrapping or cladding needed to cover it. The lateral area leaves out the base or bases, and on a round solid it is called the curved surface area. Which one you need depends on the job. A tank with a lid needs the total; a pipe needs only the curved part.
Cube: A = 6 × a²
Rectangular prism: A = 2 × (l × w + l × h + w × h)
Cylinder: A = 2 × π × r × h + 2 × π × r²
Cone: A = π × r × s + π × r², where s = √(r² + h²)
Sphere: A = 4 × π × r²
Hemisphere: A = 2 × π × r² + π × r² = 3 × π × r²
Square pyramid: A = a² + 2 × a × s, where s = √(h² + (a ÷ 2)²)
Triangular prism: A = (a + b + c) × L + 2 × (area of the triangle)
Capsule: A = 2 × π × r × h + 4 × π × r²
Here a is an edge of a cube or the base edge of a pyramid; l, w and h are length, width and height; r is a radius; h is the vertical height of a cylinder, cone or pyramid, or the length of a capsule’s straight section; s is a slant height, measured along the sloping surface; a, b and c are the sides of a prism’s triangular end and L is its length. In each formula with two terms, the first is the lateral or curved part and the second is the base or bases.
Worked example: a cylinder
A tin with a radius of 3 cm and a height of 10 cm.
- Curved surface. Unrolled, the label is a rectangle as wide as the circumference and as tall as the tin: 2 × π × 3 × 10 = 188.4956 cm².
- One end. π × 3² = 28.2743 cm².
- Both ends. 2 × 28.2743 = 56.5487 cm².
- Total. 188.4956 + 56.5487 = 245.0442 cm².
If the tin has no lid, add only one end: 188.4956 + 28.2743 = 216.7699 cm². The calculator lists each part separately so you can add up exactly the faces your job needs.
Where the formulas come from
Every formula here comes from flattening the solid into a net. A box unfolds into six rectangles in three matching pairs. A cylinder becomes a rectangle and two circles. A cone’s curved surface opens out into a sector of a circle whose radius is the slant height, and that sector has area π × r × s. A pyramid’s sides are four triangles, each with a base of a and a height equal to the slant height, giving 4 × ½ × a × s.
The sphere cannot be flattened, but Archimedes proved a striking fact about it: its surface is exactly equal to the curved surface of the cylinder that just encloses it. That cylinder has radius r and height 2r, so its curved area is 2 × π × r × 2r = 4 × π × r². For the Earth, with a mean radius of 6,371 km, that is about 510 million km².
Common mistakes
Vertical height where slant height belongs
A cone with a radius of 3 and a vertical height of 4 has a slant height of √(9 + 16) = 5. Its curved surface is π × 3 × 5 = 47.1239 and its total surface is 75.3982. Putting the vertical height into π × r × s gives 37.70, which is 20% too small. The same trap applies to pyramids: one with a base edge of 6 and a height of 4 also has a slant height of 5, so its four sides total 60 and the whole surface is 96. Enter the vertical height here and the calculator finds the slant height for you.
Counting faces that are not there
A solid hemisphere of radius 5 has a curved surface of 157.0796 and a flat circular face, 235.6194 in total. A bowl has no flat face, so only the first figure applies. Likewise, the four walls of a room 4 m by 3 m and 2.4 m high come to 2 × 2.4 × (4 + 3) = 33.6 m², while all six surfaces come to 57.6 m². Painting the walls only needs the lateral figure, less doors and windows.
Units and scale
Keep every length in the same unit before you start, and remember that the answer is in square units. A square metre is 10,000 cm², not 100. Because area depends on length squared, doubling every dimension of a solid multiplies its surface area by 4, while its volume grows eightfold. That is why large tanks are cheaper per litre to build than small ones.