CalcTrace

Circle Calculator

Enter any one of a circle’s radius, diameter, circumference or area and get the other three. Add a central angle to find the arc length, sector area, chord length and segment area as well. The diagram shows which part is which.

Last updated .

What you know

I know the

Any unit. Lengths come out in the same unit and areas in that unit squared.

The angle at the centre between two radii. Leave it empty if you only need the whole circle.

Angle is in

Result

Area

–

Show the working

    The circle formulas

    Every measurement of a circle follows from its radius r, the distance from the centre to the edge. The diameter d is the full width through the centre, the circumference C is the distance around, and A is the area enclosed. The constant π (pi) is the ratio of any circle’s circumference to its diameter, roughly 3.14159.

    d = 2 × r    C = 2 × π × r = π × d    A = π × r²

    Working backwards, r = C ÷ (2π) and r = √(A ÷ π). Add a central angle θ, measured in radians, and four more quantities follow:

    Arc length = r × θ

    Sector area = ½ × r² × θ

    Chord length = 2 × r × sin(θ ÷ 2)

    Segment area = ½ × r² × (θ − sin θ)

    The arc is the curved piece of the edge the angle cuts off. The sector is the pizza-slice region between the two radii. The chord is the straight line joining the ends of the arc, and the segment is the sliver between the chord and the arc, which is the sector minus the triangle formed by the two radii and the chord.

    These four formulas need the angle in radians. To convert, multiply degrees by π ÷ 180: an angle of 60° is 1.0472 radians, and one radian is 57.2958°. In degrees the arc and sector are simply the fraction θ ÷ 360 of the circumference and of the area.

    Worked example

    A circle of radius 5 with a central angle of 60°.

    1. Diameter. 2 × 5 = 10.
    2. Circumference. 2 × π × 5 = 31.4159.
    3. Area. π × 5² = π × 25 = 78.5398.
    4. Angle in radians. 60 × π ÷ 180 = 1.0472.
    5. Arc length. 5 × 1.0472 = 5.2360, which is one-sixth of the circumference.
    6. Sector area. ½ × 25 × 1.0472 = 13.0900.
    7. Chord. 2 × 5 × sin 30° = 10 × 0.5 = 5. At 60° the chord equals the radius, because the two radii and the chord form an equilateral triangle.
    8. Segment area. That triangle has area 10.8253, so the segment is 13.0900 − 10.8253 = 2.2647.

    Where the area formula comes from

    Slice a circle into many thin wedges and lay them side by side, alternately pointing up and down. They form a shape very close to a rectangle whose height is the radius and whose width is half the circumference, π × r. Height times width gives π × r × r. The thinner the wedges, the closer the fit, and in the limit it is exact.

    Measuring real circles

    You often cannot reach the centre of a circle, which is why the calculator accepts the circumference. Wrap a tape around a tree trunk and read 2 m; the diameter is 2 ÷ π = 0.6366 m. Going the other way, a round garden bed that has to cover 20 m² needs a radius of √(20 ÷ π) = 2.5231 m.

    The most expensive mistake is using the diameter where the formula wants the radius. Because the radius is squared, the error does not double the area, it quadruples it: a circle 10 across has an area of 78.54, but putting 10 into π × r² gives 314.16. Always halve the diameter first.

    The second trap is the angle unit. Putting 60 into r × θ without converting gives an arc many times longer than the whole circle. If an arc comes out longer than the circumference, the angle went in as degrees.

    Finally, the value of π matters less than people think. The schoolroom fraction 22 ÷ 7 is about 0.04% too high and 3.14 is about 0.05% too low, either of which is far smaller than the error in most tape measurements. This calculator uses the full double-precision value.