CalcTrace

Asphalt and Paving Calculator

Find how much asphalt to order for a driveway, path or car park. Enter the area and the compacted thickness for the volume, and the mix density for the weight in tonnes, or in US short tons if you switch to imperial. Add a waste allowance and a price per tonne for a cost estimate.

Last updated .

What are you paving?

Area
Units
m
m
mm
%
kg/m³

Compacted dense asphalt is typically about 2,350 to 2,450 kg/m³. Use the figure on the supplier's mix design if you have it.

/t

Leave blank to skip the cost. Delivery, laying and minimum charges are not included.

Result

ItemAmount

An estimate of material only. The weight depends on the density you enter, and the thickness is the finished, rolled thickness.

Show the working

    How the asphalt quantity is worked out

    Asphalt is sold by weight, but a paving job is measured by area and thickness, so the calculation goes from area to volume and then to weight using the density of the compacted mix.

    V = A × t

    A is the area to pave in square metres (length × width for a rectangle) and t the compacted thickness in metres, so 50 mm is 0.05 m. V is the compacted volume in cubic metres.

    m = V × ρ ÷ 1,000   (tonnes)

    ρ (rho) is the compacted mix density in kg/m³; dividing by 1,000 turns kilograms into tonnes. A tonne is 1,000 kg.

    morder = m × (1 + waste ÷ 100),   cost = morder × price per tonne

    The waste allowance covers edges, hand-work, the material left in the paver and trucks, and uneven base levels.

    Worked example: a 20 m × 4 m driveway, 50 mm thick

    1. Area. 20 × 4 = 80 m².
    2. Volume. 80 × 0.05 = 4 m³ of compacted asphalt.
    3. Weight. 4 × 2,400 = 9,600 kg, which is 9.6 tonnes.
    4. Waste. With 5% waste, 9.6 × 1.05 = 10.08 tonnes to order.
    5. Cost. At an example price of $150 per tonne, 10.08 × 150 = $1,512.

    At the ends of the typical density range the same driveway weighs 4 × 2,350 = 9,400 kg or 4 × 2,450 = 9,800 kg, a spread of 400 kg before waste. That is why the supplier's mix density is worth asking for on a large job.

    Imperial units and US short tons

    In imperial mode the area is in square feet, the thickness in inches and the density in pounds per cubic foot. The volume in cubic feet is area × thickness ÷ 12, and dividing by 27 gives cubic yards. The weight in pounds is volume × density, and a US short ton is exactly 2,000 lb. Because the pound is defined as exactly 0.45359237 kg, a short ton is exactly 907.18474 kg, so one tonne is about 1.1023 short tons and 1 lb/ft³ is about 16.018 kg/m³. The default 2,400 kg/m³ is about 149.83 lb/ft³.

    For example, 1,000 ft² at 2 in thick is 1,000 × 2 ÷ 12 = 166.67 ft³, or 6.17 yd³. At 150 lb/ft³ that weighs 25,000 lb, which is 12.5 short tons, and 13.125 short tons with 5% waste. At an example $140 per short ton, the material costs $1,837.50. The metric driveway above, 10.08 tonnes, is 11.11 short tons.

    Reading the result and common mistakes

    Compacted versus loose thickness. Asphalt is laid loose and rolled down. Enter the finished thickness you want after rolling: the density used here is the compacted density, so the two match. Using a loose thickness with a compacted density overstates the order.

    Tonnes and short tons. A price per tonne and a price per short ton differ by about 9%. In imperial mode the price box is per short ton; switching units converts it.

    Thin layers on a rough base. A base that dips or has potholes takes extra material that the area × thickness formula cannot see. Raise the waste allowance, or measure the low spots separately.

    Density varies by mix. Open-graded and porous mixes are lighter than dense-graded asphalt, and a mix with heavy aggregate can be denser. The 2,350 to 2,450 kg/m³ range is a typical figure for dense mixes only.

    What is not included. The base course, tack or prime coat, edge restraints and the cost of laying are separate items. This calculator gives the asphalt quantity and its material cost only.