Reading a tyre size
A metric tyre size such as 225/45R17 91W packs several measurements into one code:
- 225 is the section width: the width of the inflated tyre from sidewall to sidewall, in millimetres, measured on its specified rim.
- 45 is the aspect ratio: the sidewall height as a percentage of the section width. It is a ratio, not a measurement, so a 45-series tyre has a taller sidewall on a wider tyre.
- R is the construction: R for radial, which nearly all car tyres are. D or a dash marks diagonal (cross-ply) construction and B bias-belted. ZR is an older marking found on some high-speed radials.
- 17 is the rim diameter in inches: the diameter of the wheel the tyre fits.
- 91W is the service description: a load index and a speed symbol. They do not affect the dimensions and are looked up in the tyre maker’s tables.
A leading P marks a P-metric passenger tyre and LT a light-truck tyre; the dimensions are worked out the same way.
The formulas
Sidewall height h = W × A ÷ 100
Overall diameter D = R × 25.4 + 2 × h
Circumference C = π × D
Revolutions per km = 1,000,000 ÷ C
W is the section width in mm, A the aspect ratio in per cent, R the rim diameter in inches (25.4 mm each, exactly) and C the circumference in mm. The sidewall appears twice in the diameter because there is one above the rim and one below. For revolutions per mile, divide 1,609,344 mm by the circumference instead.
Worked example
Comparing 225/45R17 with 235/40R18:
- Sidewalls. 225 × 45 ÷ 100 = 101.25 mm, and 235 × 40 ÷ 100 = 94 mm.
- Diameters. 17 × 25.4 + 2 × 101.25 = 431.8 + 202.5 = 634.3 mm, and 18 × 25.4 + 2 × 94 = 457.2 + 188 = 645.2 mm.
- Circumference. π × 634.3 = 1,992.7 mm, so the 17-inch tyre turns 1,000,000 ÷ 1,992.7 = 501.8 times per kilometre. The 18-inch tyre turns 493.4 times.
- Difference. (645.2 − 634.3) ÷ 634.3 = 1.72% larger.
- Speedometer. The speedometer counts wheel turns, so with the larger tyre the car is going 1.72% faster than shown: an indicated 100 km/h is really 101.7 km/h, and an indicated 60 km/h is really 61.0 km/h.
Reading the result
Fitment must be checked against the vehicle maker’s specifications. The tyre placard (usually on a door pillar or in the owner’s manual) lists the sizes, load index and speed rating the maker approved. A size that matches in diameter may still rub on suspension or bodywork, need a different rim width, or be outside what the maker or local road rules allow. This calculator works out dimensions only; it does not say whether a size is suitable for a particular vehicle.
Nominal and real sizes differ. The code gives nominal dimensions. Real tyres vary slightly between brands and models, grow a little when inflated, and the tread wears down over time. Under the car’s weight the tyre also squashes, so the distance travelled per turn (the rolling circumference) is slightly less than π × D. Treat small differences as estimates.
Odometer and fuel figures shift too. The odometer is out by the same percentage as the speedometer, which affects measured fuel economy, service intervals and logbook distances.
Plus sizing. Moving to a larger rim while keeping the overall diameter close, as in the example, is called plus sizing: the sidewall gets lower to make room for the bigger wheel.