CalcTrace

One-Rep Max Calculator

Estimate your one-repetition maximum (1RM), the heaviest weight you could lift once with good technique, from a lighter set. Enter the weight and the repetitions you completed to see five published formulas, their average and the loads at common percentages.

Last updated .

Your set

Units
kg
reps

A whole number from 1 to 20. Count only full repetitions done with sound technique. Sets of 10 or fewer give the most dependable estimate.

Include the weight of the bar. For bodyweight exercises such as chin-ups, enter your body weight plus any added load.

Your result

Estimated one-rep max, average of five formulas

– kg

Enter the weight and repetitions to see the estimate.

–Lowest formula
–Highest formula
–Spread between them
–Your set as % of the estimate

By formula

FormulaEstimated 1RM

Loads at common percentages

% of 1RMLoadNearest 2.5 kg

This is an estimate from formulas, not a tested maximum. Attempting a true one-repetition maximum carries a real risk of injury, particularly without experience, a thorough warm-up and a competent spotter or safety equipment.

Show the working

    The formulas behind the result

    A one-repetition maximum (1RM) is the heaviest load a person can lift once through a full range of movement. Testing it directly is demanding, so coaches and researchers have published formulas that predict it from a lighter set taken close to the limit. In each formula below, w is the weight lifted and r is the number of repetitions completed. The answer is in the same unit as w.

    Epley

    1RM = w × (1 + r ÷ 30)

    Published by Boyd Epley in 1985. Every extra repetition adds one-thirtieth of the weight lifted.

    Brzycki

    1RM = w × 36 ÷ (37 − r)

    Published by Matt Brzycki in 1993. It rises gently at low repetitions and steeply at high ones, because the divisor shrinks as r grows.

    Lombardi

    1RM = w × r0.10

    Published by V. Patteson Lombardi in 1989. It raises the repetitions to the power of one-tenth, and gives the lowest estimate of the five for long sets.

    O’Conner

    1RM = w × (1 + r ÷ 40)

    Published by O’Conner, Simmons and O’Shea in 1989. It has the same shape as Epley with a smaller step per repetition, one-fortieth of the weight.

    Lander

    1RM = 100 × w ÷ (101.3 − 2.67123 × r)

    Published by Jeff Lander in 1985. It behaves much like Brzycki.

    The headline figure is the plain average of the five. When r is 1, the weight lifted is by definition the one-rep max, so the calculator returns it unchanged without applying the formulas.

    Worked example

    A lifter completes 5 repetitions with 100 kg:

    1. Epley. 5 ÷ 30 = 0.1667, so 100 × 1.1667 = 116.7 kg.
    2. Brzycki. 37 − 5 = 32, so 100 × 36 ÷ 32 = 112.5 kg.
    3. Lombardi. 50.10 = 1.1746, so 100 × 1.1746 = 117.5 kg.
    4. O’Conner. 5 ÷ 40 = 0.125, so 100 × 1.125 = 112.5 kg.
    5. Lander. 2.67123 × 5 = 13.356 and 101.3 − 13.356 = 87.944, so 100 × 100 ÷ 87.944 = 113.7 kg.
    6. Average. (116.7 + 112.5 + 117.5 + 112.5 + 113.7) ÷ 5 = 114.6 kg.

    The estimates run from 112.5 to 117.5 kg, a spread of 5 kg. From the average, 90% is 103.1 kg and 85% is 97.4 kg, which would be loaded as 102.5 kg and 97.5 kg on a bar with 1.25 kg plates.

    How accurate the estimate is

    The formulas agree well for short sets and drift apart as repetitions rise. At 10 repetitions with 100 kg, Epley and Brzycki both give 133.3 kg, Lander gives 134.1 kg, Lombardi 125.9 kg and O’Conner 125 kg. At 15 repetitions the range is 131.1 kg (Lombardi) to 163.6 kg (Brzycki), a gap of more than 30 kg from the same set. That is why a set of about 10 repetitions or fewer is the usual rule of thumb, and why this calculator stops at 20.

    Beyond the mathematics, several things move the true figure away from any formula:

    Using the percentage table

    Strength programs commonly set training loads as a percentage of 1RM, which is the purpose of the table under the result. The middle column is the exact figure and the last column rounds it to the nearest 2.5 kg, or 5 lb in imperial units, since those are the smallest jumps most barbells allow. Because the starting point is an estimate, treat every figure in the table as approximate and adjust to how the weight moves on the day.

    Testing a true maximum

    An estimate from a submaximal set exists precisely so that a true maximum does not have to be attempted. Lifting the heaviest possible single places very high loads on muscles, tendons and joints, and a failed attempt under a bar can cause serious injury. Anyone considering it should be experienced with the lift and have appropriate supervision and safety equipment. If you have a medical condition or an injury, speak to a doctor or physiotherapist before heavy lifting.