Molarity and how it is calculated
Molarity, or molar concentration, is the amount of a dissolved substance per litre of the finished solution. Its unit is moles per litre (mol/L), written M.
n = m ÷ M c = n ÷ V
c = m ÷ (M × V) m = c × V × M V = m ÷ (M × c)
n is the amount of solute in moles, m its mass in grams, M its molar mass in grams per mole, V the volume of the solution in litres and c the molarity in mol/L. The calculator converts milligrams, microlitres, millimolar and so on to grams, litres and mol/L before applying the formula.
Dilution
C₁ × V₁ = C₂ × V₂
C₁ and V₁ are the concentration and volume of the stock solution you take, and C₂ and V₂ the concentration and volume of the diluted solution. Adding solvent changes the volume but not the amount of solute, so the moles before and after are equal. The two volumes can be in any unit as long as they match, and so can the two concentrations.
Worked examples
- Molarity. 5.844 g of sodium chloride, molar mass 58.44 g/mol, made up to 250 mL. n = 5.844 ÷ 58.44 = 0.1 mol, and 250 mL is 0.25 L, so c = 0.1 ÷ 0.25 = 0.4 M.
- Making a solution. For 500 mL of 0.1 M sodium chloride: m = 0.1 × 0.5 × 58.44 = 2.922 g. Weigh 2.922 g, dissolve it in less water than you need, then add water up to the 500 mL mark of a volumetric flask and mix.
- Diluting a stock. To make 250 mL of 0.1 M from a 1 M stock: V₁ = C₂ × V₂ ÷ C₁ = 0.1 × 250 ÷ 1 = 25 mL. Measure 25 mL of stock and make it up to 250 mL. Diluting 10 mL of 2 M to 0.5 M gives V₂ = 2 × 10 ÷ 0.5 = 40 mL.
Mistakes that change the answer
“Made up to” is not “added to”. Molarity uses the volume of the finished solution. Dissolving 58.44 g of salt in 1 L of water gives a little more than 1 L of solution, so slightly less than 1 M. Dissolve first, then bring the volume to the mark. In the dilution example, likewise, make the 25 mL of stock up to 250 mL rather than adding exactly 225 mL of water, because volumes of mixed liquids do not always add exactly.
Using the wrong molar mass. Many solids are sold as hydrates. Copper(II) sulfate pentahydrate, CuSO₄·5H₂O, has a molar mass of about 249.68 g/mol, while the anhydrous salt is about 159.60 g/mol. Weighing the hydrate but using the anhydrous figure gives a solution only 159.60 ÷ 249.68 = 63.9% as strong as intended.
Mixing up units. 1 M is 1,000 mM, and 1 mM is 1,000 µM. Forgetting to turn millilitres into litres makes the answer 1,000 times out.
Moles of what? 0.1 M calcium chloride, CaCl₂, contains 0.2 mol/L of chloride ions, because each formula unit releases two. Molarity refers to the formula you used for the molar mass.
Where the simple formulas stop
Molarity depends slightly on temperature, because solutions expand when warmed while the amount of solute stays the same. For work across temperatures chemists use molality, moles per kilogram of solvent, which does not change. The formulas also assume the solute dissolves completely and the stated purity is 100%; for a reagent that is 98% pure, divide the mass needed by 0.98. Very concentrated solutions and gases dissolved under pressure behave less simply, and lab protocols should be followed where they give their own procedure.