CalcTrace

Body Fat Calculator

Estimate body fat percentage with a tape measure, using the circumference method developed for the US Navy. Add your weight to see how the result splits into fat mass and lean mass.

For adults. Last updated .

Your measurements

Units
Sex used by the formula

The method has only a female and a male formula. Choose the one that best matches your body.

cm
cm

Just below the larynx (Adam’s apple), tape snug and level.

cm

At the narrowest point of the abdomen, after breathing out normally.

cm

Around the widest part of the buttocks, tape level.

kg

Only used to work out fat mass and lean mass.

Your result

Estimated body fat, US Navy method

–

Enter your measurements to see the estimate.

–Fat mass
–Lean mass
–Body density, g/cm³
–Waist + hip − neck

Share of body weight

    A tape measure estimate can sit several percentage points away from a laboratory measurement, and small tape errors move the result. It is most useful for following your own change over time, measured the same way each time. How to measure.

    Show the working

      The US Navy circumference method

      This method estimates body fat from a few tape measurements and height. It was developed by Hodgdon and Beckett at the US Naval Health Research Center as a quick field check that needs no equipment beyond a tape. Their equations predict body density, the body’s mass per unit of volume. Fat is less dense than muscle and bone, so a lower density means a higher share of fat.

      Male: D = 1.0324 − 0.19077 × log₁₀(waist − neck) + 0.15456 × log₁₀(height)

      Female: D = 1.29579 − 0.35004 × log₁₀(waist + hip − neck) + 0.22100 × log₁₀(height)

      D is body density in grams per cubic centimetre. Waist, hip, neck and height are all in centimetres, and log₁₀ is the base-10 logarithm. Density is then turned into a fat percentage with the Siri equation:

      Body fat % = 495 ÷ D − 450

      With body weight W, the split follows directly:

      Fat mass = W × body fat % ÷ 100, and lean mass = W − fat mass

      Lean mass here means everything that is not fat: muscle, bone, organs and water. A version of the method written for inches folds everything into a single equation. It gives answers a fraction of a percentage point away from the metric equations above, so this calculator converts inches to centimetres and uses the metric form for everyone.

      Worked example

      A man is 180 cm tall with a 38 cm neck and a 90 cm waist, and weighs 80 kg.

      1. Circumference value. 90 − 38 = 52 cm.
      2. Logarithms. log₁₀(52) = 1.7160 and log₁₀(180) = 2.2553.
      3. Body density. 1.0324 − 0.19077 × 1.7160 + 0.15456 × 2.2553 = 1.0324 − 0.3274 + 0.3486 = 1.0536.
      4. Body fat. 495 ÷ 1.0536 − 450 = 19.8%.
      5. Fat and lean mass. 80 × 19.8 ÷ 100 = 15.8 kg of fat, leaving 64.2 kg of lean mass.

      For a woman who is 165 cm tall with a 32 cm neck, 75 cm waist and 98 cm hips, the circumference value is 75 + 98 − 32 = 141 cm and the same steps give 28.9%.

      How to measure each site

      Use a flexible, non-stretch tape. Measure against bare skin, pull the tape snug without pressing into the skin, and keep it level all the way around. Stand upright and relaxed, and do not hold your stomach in.

      Take each measurement two or three times and use the average. The waist carries the most weight in the formula: for the man in the example, a waist one centimetre larger raises the result by about 0.7 of a percentage point. Measuring at the same time of day, in the same way, matters more than the exact figure.

      What the result can and cannot tell you

      The method was fitted to a particular group, serving military personnel, and it assumes body fat is carried in the usual places. It tends to be less reliable for people whose shape differs from that group: very lean athletes, people who carry little fat around the waist, older adults, and anyone whose waist is changed by pregnancy or a medical condition. The equations can even return a negative or impossibly high figure for unusual combinations of measurements. When that happens the calculator shows a dash instead of a number.

      No tape method measures fat directly. Laboratory methods such as a DEXA scan or underwater weighing are closer to the truth, and even they rest on assumptions. Treat this result as an estimate with a margin of several percentage points either way. Its real strength is tracking: if your measurements are taken consistently, the direction of change over months is far more trustworthy than any single reading.

      This page does not label results as good or bad. Healthy body fat levels differ with age, sex and individual circumstances, and that judgement belongs in a conversation with a health professional.