CalcTrace

Sleep Calculator

Pick the time you need to wake up and see when to go to bed so that the alarm falls at the end of a whole sleep cycle. Or enter a bedtime and see the matching wake-up times. The cycle length and the time it takes you to fall asleep are yours to set.

Last updated .

Your night

What do you know?
min
min

90 minutes and 15 minutes are commonly quoted averages, not measurements of you. Both vary between people and from night to night, so change them if you know your own.

Result

Result

–

–Time asleep
–Time in bed
–Asleep by
–Cycles

Every option from 1 to 8 cycles

CyclesGo to bed atAsleep byTime asleep

Show the working

    How the times are worked out

    Sleep is not one even state. Through the night the body moves through lighter and deeper stages in a repeating pattern, and each pass through the pattern is called a sleep cycle. The idea behind a sleep calculator is simple: an alarm that goes off near the end of a cycle, when sleep is lighter, is often reported to be easier to wake to than one that goes off in the middle of deep sleep. So the calculator counts in whole cycles.

    Time asleep = number of cycles × cycle length

    Bedtime = wake-up time − time asleep − time to fall asleep

    Wake-up time = bedtime + time to fall asleep + time asleep

    The cycle length and the time to fall asleep are both in minutes. The time to fall asleep matters because cycles start when you fall asleep, not when you get into bed. The calculator starts with a 90-minute cycle and 15 minutes to fall asleep. These are widely quoted round figures for adults, used here as starting assumptions and nothing more. Real cycles differ from person to person, change with age, and are not all the same length within a single night.

    Worked example: waking at 6:30 am

    Take a 6:30 am alarm, a 90-minute cycle and 15 minutes to fall asleep, and aim for five cycles.

    1. Time asleep. 5 × 90 = 450 minutes, which is 7 hours 30 minutes.
    2. Add the time to fall asleep. 450 + 15 = 465 minutes, or 7 hours 45 minutes in bed.
    3. Count back from the alarm. 6:30 am less 6 hours 30 minutes is midnight, and a further 1 hour 15 minutes back is 10:45 pm. Get into bed at 10:45 pm, be asleep by 11:00 pm.

    The neighbouring options are one cycle apart: 9:15 pm for six cycles (9 hours asleep), 12:15 am for four cycles (6 hours) and 1:45 am for three (4 hours 30 minutes). Working forwards uses the same sums. Get into bed at 11:00 pm, fall asleep at 11:15 pm, and five cycles end at 6:45 am, six at 8:15 am.

    How far to trust the result

    The arithmetic is exact. The inputs are not, and the error grows with every cycle counted. Suppose your cycles really average 100 minutes, not 90. For the 6:30 am alarm and five cycles, the sum becomes 5 × 100 + 15 = 515 minutes, and the bedtime moves from 10:45 pm to 9:55 pm, 50 minutes earlier. Ten minutes of error per cycle has become 50 minutes after five cycles, which is more than half of a 90-minute cycle. At that point the alarm is no more likely to land at the end of a cycle than anywhere else.

    Three practical consequences follow:

    What this calculator does not tell you

    It does not say how much sleep you need. That depends on age, health and the individual, and no number of cycles is recommended here: the option shown as the main result is simply the one you select. The table lists every option from one cycle to eight so that you can see the trade-off between an earlier night and a later one, with the total time asleep beside each.

    It also assumes an unbroken night. Waking during the night, alcohol, caffeine, shift work, illness and some medicines all change how sleep is structured, and a simple count of cycles cannot allow for them. If you are often tired despite spending enough time in bed, or you have trouble falling or staying asleep, that is a question for a doctor, not a calculator.

    Using the times